Exactly how to Replace a Tub (Step By Step).
Exactly how to Replace a Tub (Step By Step).
Blog Article
The article in the next paragraphs involving How to Install a Bathtub Yourself is highly stimulating. Check it out for your own benefit and figure out what you think about it.
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can move speedily; if you have to open a wall to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This article will help you install a brand-new bath tub in your washroom if you have actually currently gotten a new tub and don't require to alter the plan of your previous supply of water pipelines.
Your devices as well as material list must make up the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making sure that the washers are in area between the faucet and also the sink. Secure the tap in place with the supplier given backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, position the bath tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bath tub until the level checks out level.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the ideal supply pipe by making a compression join; after that do the very same for the other faucet.
Switch on the supply of water as well as inspect all joints as well as new pipework for leaks and tighten them if required. Fill up the tub and additionally examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been made use of at the very least when as this will settle it into its last setting.
Getting ready for the Setup
Firstly, the supporting structure supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can break rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads about How to Install a Bathtub, I thought sharing that piece of content was really helpful. Appreciated our content? Please share it. Let other people check it out. I treasure reading our article about Installing A Bathtub.
Get Quote Report this page